View MSK4250H_1284388.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ISO 9001 CERTIFIED BY DSCC
M.S.KENNEDY CORP.
4707 Dey Road Liverpool, N.Y. 13088
10 AMP, 75V, H-BRIDGE MOSFET BRUSHED MOTOR CONTROLLER
4250
(315) 701-6751
FEATURES:
MIL-PRF-38534 QUALIFIED
75 Volt Motor Supply Voltage 10 Amp Output Switch Capability 100% Duty Cycle High Side Conduction Capable Shoot-Through/Cross Conduction Protection "Real" Four Quadrant Torque Control Capability Good Accuracy Around the Null Torque Point
DESCRIPTION:
The MSK 4250 is a complete H-bridge MOSFET Brushed Motor Control System in an electrically isolated hermetic package. The hybrid is capable of 10 amps of output current and 75 volts of DC bus voltage. It has the normal features for protecting the bridge. Included is all the bridge drive circuitry, and all the current sensing and analog circuitry necessary for closed loop current mode (torque) control. When PWM'ing, the transistors are modulated in locked anti-phase mode for the tightest control and the most bandwidth. Provisions for applying different compensation schemes are included. The MSK 4250 has good thermal conductivity of the MOSFET's due to isolated substrate/ package design that allows direct heat sinking of the hybrid without insulators.
EQUIVALENT SCHEMATIC
TYPICAL APPLICATIONS
Brushed DC Motor Control Servo Control Fin Actuator Control Voice Coil Control Gimbal Control AZ-EL Control
1 PRELIMINARY Rev. - 11/00
ABSOLUTE MAXIMUM RATINGS
V+ High Voltage Supply VIN Current Command Input +Vcc -Vcc IOUT Continuous Output Current IPK Peak Output Current

-55C to +125C +150C

ELECTRICAL SPECIFICATIONS
All Ratings: Tc=+25C Unless Otherwise Specified Parameter
POWER SUPPLY REQUIREMENTS +Vcc -Vcc PWM Free Running Frequency CONTROL Transconductance Current Monitor 7 Output Offset ERROR AMP Input Voltage Range 1 Slew Rate 1 Output Voltage Swing 1 Gain Bandwidth Product 1 Large Signal Voltage Gain 1 OUTPUT Rise Time 1 Fall Time 1 1 @ 64V, +150C Junction @ 10 Amps @10Amps, +150C Junction @ 10 Amps, 150C Junction @ 10 Amps, Each FET IF=10 Amps, di/dt=100A/S 1 Leakage Current 100 100 280 2 750 0.3 0.6 0.026 2.6 100 100 280 2 750 0.3 0.6 0.026 2.6 nSec nSec Amps Volts Volts Volts nSec Sec 11 6.5 12 175 12 8 13 6.5 275 11 6.5 12 175 12 8 13 6.5 275 Volts V/Sec Volts MHz V/mV 7 8 Amps Output 8 Amps Output @ 0 Volts Command 4,5,6 4,5,6 4 5,6 1.9 0.45 2 0.5 5.0 2.1 0.55 25.0 50.0 1.8 0.45 2 0.5 5.0 2.2 0.55 35.0 Amp/Volt V/Amp mAmp mAmp 4,5,6 15 16 18 14 16 19 KHz @ +15V @ -15V 1,2,3 1,2,3 60 16 85 35 60 16 85 35 mA mA
Test Conditions
Group A Subgroup
MSK 4250H Min. Typ.
3
Max. Min.
MSK 4250 Typ.
2
Max.
45
Voltage Drop Across Bridge (1 Upper and 1 Lower) 1 Voltage Drop Across Bridge (1 Upper and 1 Lower) 1 Drain-Source On Resistance (Each MOSFET) 6 Diode VSD 1 trr 1 Dead Time
NOTES: 1 2 3 4 5 6 7 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified. Military grade devices ("H" Suffix) shall be 100% tested to Subgroups 1, 2, 3 and 4. Subgroups 5 and 6 testing available upon request. Subgroup 1, 4 TA = TC = +25C 2, 5 TA = TC = +125C 3, 6 TA = TC = -55C This is to be used for MOSFET thermal calculation only. Measurements do not include offset current at 0V current command. 2 PRELIMINARY Rev. - 11/00

75V 13.5V +16V -18V 10A 20A

JC Thermal Resistance TST Storage Temperature Range TLD Lead Temperature Range (10 Seconds) TC Case Operating Temperature TJ Junction Temperature
3.1C/W -65C to +150C +300C

Units
APPLICATION NOTES MSK 4250 PIN DESCRIPTIONS
AV+, BV+ - are the power connections from the hybrid to the bus. All pins for the motor voltage supply should be connected together to share the current through the pins in the hybrid. The external wiring to these pins should be sized according to the RMS current required by the motor. A high quality monolithic ceramic capacitor for high frequencies and enough bulk capacitance for keeping the V+ supply from drooping should bypass these pins. 1000F is recommended. Capacitors should be placed as close to these pins as practical. AO, BO - are the connections to the motor phase windings from the bridge output. The wiring to these pins should be sized according to the required current by the motor. There are no short circuit provisions for these outputs. Shorts to V+ or gound from these pins must be avoided or the bridge will be destroyed. All pins for each phase should be connected together to share the current through the three pins in the hybrid. RTN - is the power return connection from the module to the bus. All internal ground returns connect to this point inside the hybrid. All three pins should be connected together to share the current. All capacitors from the V+ bus should connect to this point as close as possible. All external V+ return connections should be made as close to these pins as possible. Wiring sizing to this pin should be made according to the required current. GND - is the return point for the low powered circuitry inside the hybrid. All GND pins should be tied together. All capacitors for bypassing the + and -15V supplies should be tied at this point, as close to the pins as possible. Any ground plane connections for low powered and analog citcuitry outside the hybrid should be tied to this point. +15VIN - is the input for applying +15 volts to run the low power section of the hybrid. Both pins should be used together for optimum operation. These pins should be bypassed with a 10F capacitor and a 0.1F capacitor as close to these pins as possible. -15VIN - is the input for applying -15 volts to run the low power section of the hybrid. Both pins should be used together for optimum operation. These pins should be bypassed with a 10F capacitor and a 0.1F capacitor as close to these pins as possible. SENSE RESISTOR + - is the top of the sense resistor for sensing the bridge current and closing the loop. The bottom of the sense resistor is RTN. All the AV- and BV- pins should be connected to this point. AV-,BV- - are the power pins for the bottom of the bridge. These are to be connected to sense resistor +. DISABLE - is a pin for externally disabling the output bridge. A TTL logic low will enable the bridge and a TTL high will disable it. It is internally pulled up by a 100Amp pull-up. CURRENT COMMAND (+,-) - are differential inputs for controlling the module in current mode. Scaled at 2 amps per volt of input command, the bipolar input allows both forward and reverse current control capability regardless of motor commutation direction. The maximum operational command voltage should be 5 volts for 10 amps of motor current. Going beyond 5 volts of command voltage will force the bridge to conduct more than the desired maximum current. There is internal current limiting that will ultimately limit the absolute maximum current being output by the bridge. CURRENT MONITOR- is a pin providing a current viewing signal for external monitoring purposes. This is scaled at 2 amps of motor current per volt output, up to a maximum of 5 volts, or 10 amps. Going beyond the 5 volt maximum may result in clipping of the waveform peaks.
IN
E/A OUT - is the current loop error amplifier output. It is brought out for allowing various loop compensation circuits to be connected between this and E/A-. E/A- - is the current loop error amplifier inverting input. It is brought out for allowing various loop compensation circuits to be connected between this and E/A OUT.
3
PRELIMINARY
Rev. - 11/00
APPLICATION NOTES CONTINUED
BUS VOLTAGE FILTER CAPACITORS The size and placement of the capacitors for the DC bus has a direct bearing on the amount of noise filtered and also on the size and duration of the voltage spikes seen by the bridge. What is being created is a series RLC tuned circuit with a resonant frequency that is seen as a damped ringing every time one of the transistors switches. For the resistance, wire resistance, power supply impedance and capacitor ESR all add up for the equivalent lumped resistance in the circuit. The inductance can be figured at about 30 nH per inch from the power supply. Any voltage spikes are on top of the bus voltage and the back EMF from the motor. All this must be taken into account when designing and laying out the system. If everything has been minimized, there is another solution. A second capacitance between 5 and 10 times the first capacitor and it should either have some ESR or a resistor can be added in series with the second capacitor to help damp the voltage spikes.
Be careful of the ripple current in all the capacitors. Excessive ripple current, beyond what the capacitors can handle, will destroy the capacitors. 15VIN FILTER CAPACITORS It is recommended that about 10 F of capacitance (tantalum electrolytic) for bypassing the + and -15V inputs be placed as close to the module pins as practical. Adding ceramic bypass capacitors of about 0.1 F or 1 F will aid in suppressing noise transients. GENERAL LAYOUT Good PC layout techniques are important. Ground planes for the analog circuitry must be used and should be tied back to the small signal grounds, pins 17,18,23,24,33 and 34. The high power grounds (RTN) pins 1,2 and 3 get tied back to the small signal ground internally. DO NOT connect these grounds externally. A ground loop will result. LOW POWER STARTUP When starting up a system utilizing the MSK 4250 for the first time, there are a few things to keep in mind. First, because of the small size of the module, short circuiting the output phases either to ground or the DC bus will destroy the bridge. The current limiting and control only works for current actually flowing through the bridge. The current sense resistor has to see the current in order for the electronics to control it. If possible, for startup use a lower voltage and lower current power supply to test out connections and the low current stability. With a limited current supply, even if the controller locks up, the dissipation will be limited. By observing the E/A OUT pin which is the error amp output, much can be found out about the health and stability of the system. An even waveform with some rounded triangle wave should be observed. As current goes up, the DC component of the waveform should move up or down. At full current (with a regular supply) the waveform should not exceed +4 volts positive peak, or -4 volts negative peak. Some audible noise will be heard which will be the commutation frequency. If the motor squeals, there is instability and power should be removed immediately unless power dissipation isn't excessive due to limited supply current. For compensation calculations, refer to the block diagram for all information to determine the amplifier gain for loop gain calculations. For the power up sequence, 15 volts should be powered at the same time or before the V+ voltage is applied.
4
PRELIMINARY
Rev. - 11/00
MSK4250 TEST CIRCUIT
5
PRELIMINARY
Rev. - 11/00
MECHANICAL SPECIFICATIONS
NOTE: ALL DIMENSIONS ARE .010 INCHES UNLESS OTHERWISE LABELED.
ORDERING INFORMATION
Part Number MSK4250 MSK4250H Screening Level Industrial Military-Mil-PRF-38534
4707 Dey Road, Liverpool, New York 13088 Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products.
M.S. Kennedy Corp.
6
PRELIMINARY
Rev. - 11/00

▲Up To Search▲

Price & Availability of MSK4250H

	To Download MSK4250H Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .